HVAC & Plumbing in Maryland Heights, MO

Completed cooling tune-up on single HVAC unit located in side yard. Performed comprehensive system inspection including checking refrigerant levels, electrical connections, and airflow. Inspected air filter which showed moderate dust accumulation, examined unit labels and specifications confirming model UPF36I7ALACAAA in good operating condition for equipment under 10 years old, and documented system components with photos for service records.

Completed cooling system tune-up on single outdoor AC unit paired with Trane furnace system. Performed standard maintenance protocol including inspection of all components, refrigerant level check, electrical connections verification, and condenser coil assessment. Replaced air filter at indoor air handler to ensure proper airflow and system efficiency for the cooling season.

Excavated from meter pit to locate water line leak in lawn area. Repaired damaged section of water service line using PVC piping and fittings. Backfilled excavation and graded yard to restore lawn surface.

Performed camera location service in unfinished basement area to identify plumbing infrastructure within wall framing and concrete floor system. Documentation captured showing exposed wooden stud framing with foam insulation panels and utility connections, along with concrete floor surface conditions in renovation space requiring plumbing system assessment.

Conducted electrical estimate for Kohler generator installation. Performed site assessment and measured installation area using laser distance measuring equipment, documenting existing electrical panel configuration and available breaker spaces for generator integration. Photographed current electrical distribution panel showing circuit layout and spare capacity for proper load calculation and transfer switch planning.

Responded to no cooling complaint with indoor temperature reading 80°F despite thermostat set to 72°F. Upon inspection, found 10+ year old outdoor condenser unit with severely restricted airflow due to heavy dust, dirt, and debris accumulation blocking louver fins and grilles. Performed thorough cleaning of condenser coils and ventilation louvers, removed plant debris and obstructions from unit exterior, and restored proper airflow to system. Unit tested successfully with normal cooling operation restored.

Installed new electrical circuit and outdoor lighting fixture on existing deck structure. Routed black electrical cable along deck railing system and mounted junction box to vertical post for proper connection and code compliance. Successfully completed wiring installation with all components secured and operational.

Responded to scheduled service call for HVAC system. Upon arrival, documented existing equipment condition including electrical components, capacitor, and air handler interior before job was cancelled after dispatch. Photographed system showing wiring connections, circuit breaker, and heat exchanger coil for service records.

Completed routine cooling system tune-up on a 6-year-old residential air conditioning unit operating within normal parameters. Performed comprehensive maintenance including inspection of blower assembly and motor components, verified proper airflow through clean pleated air filter installed in ductwork, and confirmed all mechanical systems functioning correctly with no deficiencies identified.

Responded to service call for outdoor lighting circuit breaker repeatedly tripping in basement electrical panel. Diagnosed and resolved issue with 8-12 breaker controlling exterior deck lighting system. Inspected outdoor lighting fixtures and associated wiring along wooden deck area, verified proper operation of circuit, and confirmed breaker stability after repair.

Completed comprehensive cooling season tune-up on 5-year-old residential AC unit manufactured by R. Almanza Manufacturing Company. Performed standard maintenance protocol including inspection of control board, electrical connections, and ductwork insulation; all components found operating within normal parameters with no repairs required at this time.

Responded to emergency water leak call with AC system flooding above downstairs furnace. Upon arrival, found excessive condensate water accumulation requiring towel changes every one to two hours. Inspected 10-year-old ground-level outdoor unit and traced source to condensate drainage issue in attic ductwork and plenum area. Examined HVAC system components including air handler, ductwork connections, and condensate drain lines. Identified blockage or improper drainage causing water overflow from drain pan. Cleared condensate line obstruction and verified proper drainage flow. Inspected surrounding areas including water heater and furnace for any secondary water damage or related issues. Tested system operation to ensure condensate removal functioning correctly and no further leaking present. Documented equipment conditions and repair work with photographs of attic plenum assembly and utility area showing furnace and adjacent equipment.

Responded to no cooling complaint on 5-year-old ground-level unit. Upon inspection, found failed run capacitor with severe heat damage, visible burn marks, and charred terminal connections affecting compressor operation. Replaced damaged capacitor, verified proper electrical connections, and restored system to normal cooling operation.

Completed comprehensive plumbing installation and code compliance upgrade involving replacement of deteriorated cast iron waste piping with PVC throughout crawl space and vertical stack serving multiple fixtures, installation of proper venting system from basement bathroom through first floor, and water heater code upgrades including expansion tank, T&P valve, and gas line modifications. Replaced cast iron and improperly installed PVC drain lines in crawl space for kitchen and laundry with code-compliant piping and hangers, removed and replaced defective cast iron stack above basement floor serving two bathrooms including tub, shower, two lavatories and two water closets. Additional work included installation of pressure reducing valve regulator, wire stress clamp for garbage disposal power supply, removal and capping of flexible gas connector to exterior grill, and installation of 2-inch and 1.5-inch vent piping from basement bathroom reconnecting to first floor vents, all performed u

Successfully installed a whole-home dehumidifier unit in the basement mechanical area. The unit was positioned on the concrete floor, connected to electrical power, and drainage tubing was routed appropriately to handle condensate removal. System was tested and confirmed operational for humidity control.

Completed comprehensive cooling system tune-up on outdoor condenser unit located in side yard. Performed standard maintenance protocol including inspection of condenser coils, fan operation, electrical connections, and refrigerant levels. Unit operational with filter element inspected and documented; system running within normal parameters for age of equipment.

Responded to no-cool service call for ground-mounted outdoor condenser unit at Home Depot location. Upon arrival, confirmed customer complaint that fan was not engaging and system was not providing cooling. Performed diagnostic inspection of unit, removed service panel to access internal components, and assessed condenser coil condition which showed moderate accumulation of dirt and debris on aluminum fins. Completed necessary repairs to restore fan operation and cooling function, ensured unit was operating properly before departure per customer's special instructions to leave fan running with AC turned off.

Responded to no cooling complaint on single air conditioning unit located at ground level behind residence. Upon arrival, found system had experienced evaporator coil freeze-up requiring manual defrost before service could be performed. Connected refrigerant gauges to condenser unit to diagnose cooling issue and verify system pressures after coil thawing was complete.

Responded to no cooling call on 2-year-old system experiencing repeated freeze-up conditions. Upon arrival, unit had been shut down per instructions with thermostat set to fan only mode. Performed diagnostic inspection revealing corrosion and oxidation present on electrical terminal connections and mechanical components. Documented electrical terminal block condition showing rust formation on brass contacts and mounting hardware, as well as corrosion on internal mechanical assembly near spring mechanism. Verified warranty coverage status on recently installed 2024 equipment and photographed affected components for documentation purposes.

Responded to service call for slow-draining bathroom sink and clogged kitchen double sink. Upon inspection, discovered significant accumulation of hair and organic debris in bathroom sink drain, causing restricted water flow. Removed drain stopper assembly and manually extracted blockage material from P-trap area. In kitchen, assessed double sink configuration and cleared complete obstruction using appropriate drain cleaning methods. Verified proper drainage flow restored to both fixtures. All plumbing components inspected and confirmed to be functioning correctly upon completion.